It helps if you start from the inside and press towards the outside. *For larger designs, applying the tape as you pull it off the roll can be easier than cutting the whole piece off first.Ĭarefully apply the transfer tape to your design, trying to prevent bubbles and creases. Take the roll of transfer tape and pull loose enough to cover your design, then cut that piece off the roll. Make sure the surface where you will be applying your work is clean and dry. If you have extra pieces that are at least 2” x 4”, please place them in the scrap bin. Use scissors to cut your design off the roll(No blades on the machine please!).
Or, hit “Offline” on the machine and the down arrow until enough material is exposed that you can cut off your work. Release the clamps and pull the vinyl out of the back of the machine.Ģ. Once it is done, if the machine didn’t advance enough vinyl to reveal your image, either:ġ. When you are satisfied with your settings and double-checked that the vinyl cutter machine is setup correctly, hit “Cut”. *When this is selected, you can automatically cut multiple copies of your designīy setting how many rows and columns, and you can set the distance between copies. *You can make the program separate your file into pieces if your application requires it. With which color vinyl that particular layer will need to be cut in. Technique, you can create layers in your design and designate various colors to correspond *An advanced technique, you can multicolor designs by layering pieces. >Advance Amount: will determine how much the machine spits out when it’s done. You can set the size of your material, which can be very useful if you are using a scrap piece. Here you can adjust the size and orientation of your design.Ĭonfirm that the image is the correct dimensions.ĭeselect everything and look in the upper right hand corner again at the “Document” tab. Once you have your vector file created and ready to cut, click on your design, look in the upper right hand corner at the “Position & Size” tab. Or use Inkscape to import images and manipulate them into vectors. Instead, use Inkscape to create images from scratch. It only has simple text, path, and node tools and would be time consuming to create a complex design. It is difficult to create vectors in SCAL.
HOW DO YOU USE A IMAGE ON SURE CUTS A LOT 3 PRO HOW TO
The vector file tells the machine where and how to move the blade. Preparing and Cutting your File in Sure Cuts A Lot:Ī vector image is points connected by paths forming an image. Remember to change back to default settings and retract the blade back when you're done. *Note: If cutting HTV (Heat Transfer Vinyl), extend the blade out a bit, and use 200g pressure and 120 mm/s speed. Once you are happy with the position of the blade holder, hit “Origin”.Ĭonfirm that the Speed is set to 300 mm/s and the Pressure to 040g. You do not want the machine to have to pull the roll because it wears out the motors faster. If cutting a larger or longer piece, make sure that as much vinyl as you will use has been unwound from the roll. Watch that the blade holder is consistently the same distance from the edge. Tip: To make sure that your vinyl is square, position the blade holder in the lower right corner and use the arrow keys to move the vinyl forward and backward. There should be vinyl at least ½” to the left and below the blade holder. Use the up, down, left, and right arrows to position the blade holder inside the lower right corner of your vinyl. Once your vinyl is locked down, hit “Offline”. Note: Make sure the support rollers are on the metal rollers and not on the black space between the metal rollers. If using a 24” or larger roll, 3 rollers should be used. If your piece is very small, you can get away with just using one. Preferably you want at least two support rollers holding you vinyl.
Square the front edge of the vinyl to the machine and lock the support roller in place by pushing the lever so that it is parallel to the ground. Insert the vinyl between the support roller and the metal roller, from back to front. Unlock the support roller by putting the lever in the up position. Note: Make sure the vinyl is coming off the back side of the roll. The vinyl should be on the right side of the machine. Place the roll of vinyl on the two rollers on the back of the machine stand. Turn on machine switch, which is on the left side of the machine. Make sure Sure Cuts a Lot is already open.
0 kommentar(er)
